Crankshaft timing hole, 2.1 td crankshaft hole| Welcome Guest ( Log In | Register ) | Resend Validation Email |
   |
Crankshaft timing hole, 2.1 td crankshaft hole| bov783 |
Posted: June 19, 2011 07:44 pm
|
|
Advanced Member  Group: Members Posts: 59 Member No.: 1382 Joined: October 04, 2008  |
Hi all
Anyone know where the crankshaft timing hole or mark is on a 2.1 td 1996. I recon I have got my timing one tooth out following a head gasket change. I did lock the pump and camshaft but not the crankshaft. I hope that if I put the two lock bolts back I should be able to use the crankshaft bolt to confirm it's all correct. Only problem is I can't find it it must be hidden by the starter motor but not sure. Regards Phil |
 
|
| lez |
Posted: June 19, 2011 08:09 pm
|
 Super Member Group: Members Posts: 224 Member No.: 397 Joined: July 09, 2006 |
-------------------- |
|
|
| robertmnorton |
Posted: June 19, 2011 08:53 pm
|
|
Super Member Group: Members Posts: 361 Member No.: 586 Joined: January 13, 2007 |
Hi Phil,i always remove the starter,there are other holes in the flywheel that make identifying the tdc hole confusing.I also use the shank of a 7.8mm drill to locate the hole,a smaller drift may pass in the wrong hole,also that an 8mm drift is too tight.Further proof that you're at tdc of #4 is to lift the valve cover and check the cam lobes of #4 cylinder.the next cam lobe actuation should be exhaust with the two inlet lobes clear. You can also remove the #4 injector (it's easier than the glowplug) and check it's on compression stroke.
robertm |
|
|
| Peter.N. |
Posted: June 19, 2011 10:17 pm
|
 Andre's Mate Group: Members Posts: 3414 Member No.: 78 Joined: August 31, 2004 |
Hi Phil
If you bend a wire coathanger into a starting handle shape (if you remember those) you can slide it along behind the starter and if you have the proportions right its quite easy to get in. Peter This post has been edited by Peter.N. on June 19, 2011 10:18 pm -------------------- Used to have:
'96 'N' 2.1 td VSX manual estate White RP6695. '01 'Y' 406 GXL Hdi 110 manual estate silver '01 C5 estate 2.0. Hdi 110hp manual Located in Charmouth, Dorset. U.K. Blower transistors MJ 11015 |
|
|
| bov783 |
Posted: June 20, 2011 07:44 am
|
|
Advanced Member Group: Members Posts: 59 Member No.: 1382 Joined: October 04, 2008 |
Thanks Peter will have a go tonight. Ps I also run a 1936 standard nine so the shapes no problem !!
|
|
|
| Peter.N. |
Posted: June 20, 2011 12:43 pm
|
|
Andre's Mate Group: Members Posts: 3414 Member No.: 78 Joined: August 31, 2004 |
You will be familier with them then
 I used to drive my bosses Standard 14, never quite sure which way it was going to go when you hit the brakes  Peter -------------------- Used to have:
'96 'N' 2.1 td VSX manual estate White RP6695. '01 'Y' 406 GXL Hdi 110 manual estate silver '01 C5 estate 2.0. Hdi 110hp manual Located in Charmouth, Dorset. U.K. Blower transistors MJ 11015 |
|
|
| bov783 |
Posted: June 20, 2011 08:34 pm
|
|
Advanced Member Group: Members Posts: 59 Member No.: 1382 Joined: October 04, 2008 |
 Why the hell did they put it behind the starter?? |
|
|
| bov783 |
Posted: June 20, 2011 08:36 pm
|
|
Advanced Member Group: Members Posts: 59 Member No.: 1382 Joined: October 04, 2008 |
 Another shot if anyone is interested |
|
|
| citroenxm |
Posted: June 21, 2011 08:14 am
|
|
Andre's Mate Group: Members Posts: 2058 Member No.: 257 Joined: October 10, 2005 |
That looks just about spot on!!
Should sound good with that setup now! Paul -------------------- 1993 K Reg 3.0 V6 12 Valve Auto (Green) LPG S1.5 SORNd
1990 H reg 3.0 V6 24 valve Manual. Grey S1 SORNd 1991 H reg 2.1 SED td Manual, Maroon. SORNd 1992 K reg 2.1 SD Manual. Getting ready to sell on 1998 V reg Xantia HDi Exclusive Silver Location: YOU'LL NEVER FIND ME!! |
|
|
| bov783 |
Posted: June 21, 2011 08:32 pm
|
|
Advanced Member Group: Members Posts: 59 Member No.: 1382 Joined: October 04, 2008 |
Thanks Paul
I am happy it ban on. Managed to do a bit more tonight will keep posting bits until the final start up. Just hope it runs ok !! If it dose work it should give some confidence to others to do it cos if I can do it anyone with a basic skill and interest can do it !!! |
|
|
0 User(s) are reading this topic (0 Guests and 0 Anonymous Users)
0 Members:
 |
|
Skin arobase par alphega @ PCentraide 2005 (original)
V1.3 par Elianora la blanche @ La Caverne de la Rose pourpre
V1.3 par Elianora la blanche @ La Caverne de la Rose pourpre
Powered by Invision Power Board(U) v1.3.1 Final © 2003 IPS, Inc.